static dissipative package to hold 50 parts 9.5mm x 3.7mm x 2.3mm.

This 10 count box is Static Dissipative.  It will hold parts .25” square x 2.8mm thick.
Call for samples and assistance.
This box can be customized to hold your specific size.  See the main image for the 10S-250 on left and two examples of customized boxes using the same exterior size. 
You can have exact interior needed and only pay for the insert to customize the existing box.

static dissipative package to hold 50 parts 6.3mm square or raound.

This 100 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts .263” long x .133” wide x .275” thick.

This 100 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts .271” long x .271” wide x .078” thick.

static dissipative package to hold 50 parts 8.3mm square or raound.

This 100 count box is Static Dissipative.  It will hold parts .5” OD x .080” thick, with the long ribbed lid shown on the right side of the cross section image below.

Using a flat lid, you can hold parts up to .937” OD.  By using ribbed lids, you can hold a range of parts, including small square parts. See examples shown in Image #1.  Call for samples and assistance.
This box can be customized to hold your specific size.
You only pay for the insert to customize the existing box.

static dissipative package to hold 10 parts 12.7 square or raound.

This 52 count box is Static Dissipative.  It will hold parts .5” OD x .080” thick,  with lid shown.

Using a deeper lid, you can hold parts up to .750” x .5”.  Call for samples and assistance.
This box can be customized to hold your specific size.
You only pay for the insert to customize the existing box.

static dissipative package to hold 10 parts 14mm x 14mm x 4mm.

This 100 count box is Static Dissipative.  It will hold parts .58” OD x .080” thick, with the long ribbed lid shown on the right side of the cross section image below.

Using a flat lid, you can hold parts up to .937” OD.  By using ribbed lids, you can hold a range of parts, including small square parts. See examples shown in Image #2.  Call for samples and assistance.
This box can be customized to hold your specific size.
You only pay for the insert to customize the existing box.

This 100 count box is Static Dissipative.  It will hold parts .688” OD x .080” thick, with the long ribbed lid shown on the right side of the cross section image below.

Using a flat lid, you can hold parts up to .937” OD.  By using ribbed lids, you can hold a range of parts, including small square parts. See examples shown in Image #2.  Call for samples and assistance.
This box can be customized to hold your specific size.
You only pay for the insert to customize the existing box.

This 50 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts .750” long x .530” wide x .239” thick.

This 100 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts .850” long x .400” wide x .100” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.03” tall.  Using lid #201-01 allows parts up to 1.44” tall to be protected.
A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 100 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts .850” long x .800” wide x .110” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.42” tall.  Using lid #201-01 allows parts up to 1.82” tall to be protected.
A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 240 count box is Static Dissipative

This 100 count box is Static Dissipative.  It will hold parts .937” OD x .080” thick, with the long ribbed lid shown on the right side of the cross section image below.

Using a flat lid, you can hold parts up to .937” OD.  By using ribbed lids, you can hold a range of parts, including small square parts. See examples shown in Image #2.  Call for samples and assistance.
This box can be customized to hold your specific size.
You only pay for the insert to customize the existing box.

This 52 count box is Static Dissipative.  It will hold parts 1.0” OD x .080” thick,  with lid shown.

Using a deeper lid, you can hold parts up to 1.250” x 1.0”.  Call for samples and assistance.
This box can be customized to hold your specific size.
You only pay for the insert to customize the existing box.

Static dissipative rack for 1” wide slides.  3” length fits using deep lid shown in cross section.  Stackaable for slides not exceeding 2.5”

This 100 count box is Static Dissipative, it has a flat lid.  It will hold parts 1.0” x .5” x .5” rectangular or cylindrical.

This tray can be customized to hold your specific size.
You only pay for the insert to customize the existing box.

This 80 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts .992” long x .550” wide x .236” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.16” tall.  Using lid #201-01 allows parts up to 1.60”. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 240 count box is Static Dissipative.  It will hold parts 1.0” square (or round) x .10”

By using deeper lids (#202 deep lid shown in cross section), you can hold taller parts.  Call for samples and assistance.
This box can be customized to hold your specific size.
You only pay for the insert to customize the existing box.

Static Dissipative box for slides sized 1.0” x 1.00” x .080”.

This 100 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 1.00” long x 1.00” wide x .118” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.63” tall.  Using lid #201-01 allows parts up to 2.06”. Using lid #102 DD Lid allows parts up to 2.62” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 80 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts .992” long x .550” wide x .236” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.16” tall.  Using lid #201-01 allows parts up to 1.60”. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.16” tall.  Using lid #201-01 allows parts up to 1.60”. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 100 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts .850” long x .400” wide x .100” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.03” tall.  Using lid #201-01 allows parts up to 1.44” tall to be protected.
A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 50 count box is Static Dissipative.  It will hold parts 1.10” Round or Square x .080” thick,  with lid shown.

This 100 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 1.4” long x .5” wide x .1” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.16” tall.  Using lid #201-01 allows parts up to 1.51” tall to be protected.
A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 100 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 1.4” long x .5” wide x .1” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.16” tall.  Using lid #201-01 allows parts up to 1.51” tall to be protected.
A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 100 count box is Static Dissipative.  It will hold parts 1.4”” x 1.0” x .10”

By using deeper lids (#202 deep lid shown in cross section), you can hold taller parts.  Call for samples and assistance.
This box can be customized to hold your specific size.
You only pay for the insert to customize the existing box.

This 50 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 1.40” long x 1.40” wide x .110” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.40” tall.  Using lid #201-01 allows parts up to 2.03”. Using lid #105 DD allows parts up to 3.00” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 100 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts .850” long x .800” wide x .110” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.42” tall.  Using lid #201-01 allows parts up to 1.82” tall to be protected.
A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 100 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts .850” long x .400” wide x .100” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.03” tall.  Using lid #201-01 allows parts up to 1.44” tall to be protected.
A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 75 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 1.5” long x 1.5” wide x .118” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 2.13” tall.  Using lid #201-01 allows parts up to 2.55”. Using lid #102 DD Lid allows parts up to 3.125” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 100 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 1.4” long x .5” wide x .1” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.16” tall.  Using lid #201-01 allows parts up to 1.51” tall to be protected.
A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 100 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 1.00” long x 1.00” wide x .118” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.63” tall.  Using lid #201-01 allows parts up to 2.06”. Using lid #105 DD allows parts up to 2.62” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 50 count tray is Static Dissipative.  It will hold parts 1.75” x .75” x .5” .

This tray can be customized to hold your specific size.
You only pay for the insert to customize the existing box.

This 240 count box is Static Dissipative.  It will hold parts 1.75” x 1.0” x .110”

By using deeper lids (#202 deep lid shown in cross section), you can hold taller parts.  Call for samples and assistance.
This box can be customized to hold your specific size.
You only pay for the insert to customize the existing box.

This 50 count tray is Static Dissipative.  It will hold parts 1.75” x 1” x .680”.

This tray can be customized to hold your specific size.
You only pay for the insert to customize the existing box.

This 100 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts .850” long x .800” wide x .110” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.42” tall.  Using lid #201-01 allows parts up to 1.82” tall to be protected.
A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 160 count box is Static Dissipative.  It will hold parts 1.99” x 1.87” x 1.87”

By using deeper lids (#202 deep lid shown in cross section), you can hold taller parts.  Call for samples and assistance.
This box can be customized to hold your specific size.
You only pay for the insert to customize the existing box.

This 50 count tray is Static Dissipative.  It will hold parts 1.90” x 1.125” x .5”.

This tray can be customized to hold your specific size.
You only pay for the insert to customize the existing box.

This 252 count box is Static Dissipative.  It will hold parts 1.96” x .860” x .125”

By using deeper lids (#202 deep lid shown in cross section), you can hold taller parts.  Call for samples and assistance.
This box can be customized to hold your specific size.
You only pay for the insert to customize the existing box.

static dissipative package to hold 25 parts 12.4” x 10.1” rectangular.

This 56 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 2.0” long x 1.0” wide x .161” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.60” tall.  Using lid #201-01 allows parts up to 2.0”. Using lid #102 DD Lid allows parts up to 2.625” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 56 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 2.0” long x 1.0” wide x .161” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.60” tall.  Using lid #201-01 allows parts up to 2.0”. Using lid #102 DD Lid allows parts up to 2.625” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 24 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 2.0” long x 1.75” wide x .50” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 2.625” tall.  Using lid #201-01 allows parts up to 3.05”. Using lid #102 DD Lid allows parts up to 3.625” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

Static dissipative 10-count box with flat lid for 2” x 2” x .062” squares.

Static dissipative 100-count box with flat lid for 2” squares.

This 56 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 2.0” long x 1.0” wide x .161” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.60” tall.  Using lid #201-01 allows parts up to 2.0”. Using lid #102 DD Lid allows parts up to 2.625” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 50 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 1.40” long x 1.40” wide x .110” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.40” tall.  Using lid #201-01 allows parts up to 2.03”. Using lid #105 DD allows parts up to 3.00” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 100 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 1.00” long x 1.00” wide x .118” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.63” tall.  Using lid #201-01 allows parts up to 2.06”. Using lid #105 DD allows parts up to 2.62” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 15 count box is Static Dissipative.  It will hold parts 5mm thick x 53.9mm wide x 83.1mm tall ( 2.122” x 3.271” x .196” thick).

This 75 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 1.5” long x 1.5” wide x .118” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 2.13” tall.  Using lid #201-01 allows parts up to 2.55”. Using lid #102 DD Lid allows parts up to 3.125” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 40 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 2.23” long x 1.25” wide x .25” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.875” tall.  Using lid #201-01 allows parts up to 2.30”. Using lid #102 DD Lid allows parts up to 2.875” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box

This 40 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 2.23” long x 1.25” wide x .25” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.875” tall.  Using lid #201-01 allows parts up to 2.30”. Using lid #102 DD Lid allows parts up to 2.875” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box

This 40 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 2.23” long x 1.25” wide x .25” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.875” tall.  Using lid #201-01 allows parts up to 2.30”. Using lid #102 DD Lid allows parts up to 2.875” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box

Static dissipative 25-count box with flat lid for 2.635” squares.

Static dissipative 45-count box with flat lid for 20400” x 5.000” x .078” Glass.

Static dissipative 36-count box with flat lid for 2.4” square.

This 50 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 1.40” long x 1.40” wide x .110” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.40” tall.  Using lid #201-01 allows parts up to 2.03”. Using lid #105 DD allows parts up to 3.00” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 50 count box is Static Dissipative.  It will hold parts 5mm thick x 52mm wide x 65mm tall ( 2.5” x 2.5” x 1.96” thick).
You can use deeper lids to hold long rectangles.  See Image #2 for examples.  Call for samples and assistance.
This box can be customized to hold your specific size.  See image #3 FOR EXAMPLES of customized boxes using the same exterior size.  You only pay for the insert to customize the existing box.

This 90 count box is Static Dissipative.  It will hold parts 2.5” x 2.5” x .065”

By using deeper lids (#202 deep lid shown in cross section), you can hold taller parts.  Call for samples and assistance.
This box can be customized to hold your specific size.
You only pay for the insert to customize the existing box.

This 50 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 2.5” long x .870” wide x .120” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.46” tall.  Using lid #201-01 allows parts up to 1.88” tall to be protected.
A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 50 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 2.5” long x .870” wide x .120” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.46” tall.  Using lid #201-01 allows parts up to 1.88” tall to be protected.
A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 50 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 2.5” long x .870” wide x .120” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.46” tall.  Using lid #201-01 allows parts up to 1.88” tall to be protected.
A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 18 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 2.5” long x 2.5” wide x .53” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 3.125” tall.  Using lid #201-01 allows parts up to 3.55”. Using lid #102 DD Lid allows parts up to 4.125” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

Static Dissipative tray for 3.100” Square slides

This 75 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 1.5” long x 1.5” wide x .118” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 2.13” tall.  Using lid #201-01 allows parts up to 2.55”. Using lid #102 DD Lid allows parts up to 3.125” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

Static Dissipative tray for 2.560” Square slides

This 100 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 1.00” long x 1.00” wide x .118” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.63” tall.  Using lid #201-01 allows parts up to 2.06”. Using lid #105 DD allows parts up to 2.62” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 36 count tray is Static Dissipative.  It will hold parts 2.625” x .75” x .5”.

This tray can be customized to hold your specific size.
You only pay for the insert to customize the existing box.

This 24 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 2.0” long x 1.75” wide x .50” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 2.625” tall.  Using lid #201-01 allows parts up to 3.05”. Using lid #102 DD Lid allows parts up to 3.625” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 56 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 2.0” long x 1.0” wide x .161” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.60” tall.  Using lid #201-01 allows parts up to 2.0”. Using lid #102 DD Lid allows parts up to 2.625” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

Static dissipative 50-count box with flat lid for 2.635” squares.

Static dissipative 20 count package for 2.732” squares or round.  This mold has numerous inserts for larger sizes up to 3.75” square or round

Static dissipative 20 count package for 2.750” squares or round.  This mold has numerous inserts for larger sizes up to 3.75” square or round.

This 30 count box is Static Dissipative.  It will hold parts 5mm thick x 72mm wide x 75mm tall ( 2.8” x 2.9” x 1.96” thick).
You can use deeper lids to hold long rectangles.  See Image #2 for examples.  Call for samples and assistance.
This box can be customized to hold your specific size.  See image #3 FOR EXAMPLES of customized boxes using the same exterior size.  You only pay for the insert to customize the existing box.

This 40 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 2.23” long x 1.25” wide x .25” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.875” tall.  Using lid #201-01 allows parts up to 2.30”. Using lid #102 DD Lid allows parts up to 2.875” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box

This 25 count box is Static Dissipative.  It will hold parts 77mm wide x 25.4mm x 1mm thick and fits in your coat pocket.  The flat lid allows for labelling of content inside.
The lid can be customized with your logo if desired.

Using a flat lid, you can hold parts 25.4mm tall.  By using deeper lids, you can hold taller parts, see examples shown in Image #2.  Call for samples and assistance.
This box can be customized to hold your specific size.  See image #1 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 50 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 1.40” long x 1.40” wide x .110” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 1.40” tall.  Using lid #201-01 allows parts up to 2.03”. Using lid #105 DD allows parts up to 3.00” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 24 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 2.0” long x 1.75” wide x .50” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 2.625” tall.  Using lid #201-01 allows parts up to 3.05”. Using lid #102 DD Lid allows parts up to 3.625” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

Static dissipative 20 count package for 3.062 inch square or round.
Rectangular parts can be held using the deep lid, available as an option.
This mold has numerous aluminum inserts to create a variety of box interiors. We can customize this box to meet your exact requirements.Drawing shows cross section of the box with a flat & deep lid.

This 75 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 1.5” long x 1.5” wide x .118” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 2.13” tall.  Using lid #201-01 allows parts up to 2.55”. Using lid #102 DD Lid allows parts up to 3.125” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 18 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 2.5” long x 2.5” wide x .53” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 3.125” tall.  Using lid #201-01 allows parts up to 3.55”. Using lid #102 DD Lid allows parts up to 4.125” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

Static dissipative 25 count package for 3” squares or round.  This mold has numerous inserts for larger sizes up to 3.75” square or round
Image 2 shows six count box for 3.5” squares up to .5” thick, #6x35

Static dissipative 25 count package for 3.25 inch square or round.
Rectangular parts can be held using the deep lid, available as an option.
This mold has numerous aluminum inserts to create a variety of box interiors. We can customize this box to meet your exact requirements.
Image 1 shows cross section of the box with a flat lid.

Static dissipative tray for 3.4” parts.  Use reversible top for full enclosure.

Static dissipative 20 count package for 3.4 inch square or round.
Rectangular parts can be held using the deep lid, available as an option. cross section of the box with a flat lid.

Static dissipative 150 count package for 3.5 x 1.75 rectangles.
Image 1 is the line drawing. This mold can be modified to accommodate your exact part by making modular aluminum inserts.

Static dissipative 20 count package for 3.5 inch square or round.
Rectangular parts can be held using the deep lid, available as an option. Image 1 shows cross section of the box with a flat lid.

This 10 count tray is Static Dissipative.  It will hold parts 3.5” x .75” x .680”.

This tray can be customized to hold your specific size.
You only pay for the insert to customize the existing box.

Static dissipative six pack for 3.5” squares, with lid.

This 18 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 2.5” long x 2.5” wide x .53” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 3.125” tall.  Using lid #201-01 allows parts up to 3.55”. Using lid #102 DD Lid allows parts up to 4.125” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

This 24 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 2.0” long x 1.75” wide x .50” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 2.625” tall.  Using lid #201-01 allows parts up to 3.05”. Using lid #102 DD Lid allows parts up to 3.625” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

Static Dissipative tray for .3.75” Square slides

Static dissipative 100-count box with flat lid for 3” squares.

Static dissipative 30 count package for glass or ceramic 4” square.  see also #25S-4062w for thicker glass and #75S-4062 for more parts per package.

Static dissipative 75 count pack for 4” squares.  see also #24S-4409 for thicker glass (up to 12.7mm) sized 4” to 4.4” square or round.  see also #75S-4562 for 3mm thick glass squares up to 4.5” square

This 18 count box is Static Dissipative.  By using #102 FLAT LID, this box will hold parts 2.5” long x 2.5” wide x .53” thick.
By using deeper lids, you can hold taller parts.  Using #102D lid shown on the drawing, this box will hold parts up to 3.125” tall.  Using lid #201-01 allows parts up to 3.55”. Using lid #102 DD Lid allows parts up to 4.125” tall to be protected. A flat polyethylene pad can be used to take up space beneath the lid if your part doesn’t go all the way up.  This prevents parts from wiggling in their respective pocket.

Call for samples and assistance.
This box can be customized to hold your specific size.  See image #2 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

Static dissipative 25 count package for 4.3 inch square or round.
Rectangular parts can be held using the deep lid, available as an option. Image 1 shows cross section of the box with a flat lid.

Static dissipative 24 count package for 4.4 x .5 inch square or round.

Static dissipative tray for 4.4” square or round, use reversible lid for full enclosure.

Static dissipative 45 count package for 3.5 x 1.75 rectangles.
Image 1 is the line drawing. This mold can be modified to accommodate your exact part by making modular aluminum inserts.

Static dissipative 75 count package for 4.5” squares or round x .125” thick.  see image 2 below #24S-4409 for thicker parts over 4” square up to 4.4” square

Static dissipative 24 count package for 4.75 x 4.25 inch square or round.
This box can be customized to meet your exact requirements.

This 25 count box is Static Dissipative.  It will hold parts 4.75” wide x 2.4mm thick.  It will hold parts 3.1” (79mm) high using a flat lid (#6575-01 lid).  By using deeper lids, you can hold taller parts, see Image #2 for examples.  Call for samples and assistance.
This box can be customized to hold your specific size.  See image #3 FOR EXAMPLES of customized boxes using the same exterior size.  You only pay for the insert to customize the existing box.

Static dissipative 36 count tray.  Reversible design allows parts 4.75” square to be enclosed.

Static dissipative 75 count box with flat lid to hold 4” squares.

This box can be customized with new mold inserts to create box meeting your exact requirements.

Static dissipative 25 count box and lid for 101mm square glass up to 4mm thick.  Great for solar cell archiving.
see also #30S-4062w for thinner glass sized 101mm x 101mm square (or round0

Static Dissipative tray with open area for 400mm x 500mm wafer. Stackable Trays.

Static dissipative 25 count package for 5 inch square or round (See also #25R-5062).
Image 1 shows cross section of the box with a flat lid.

Static dissipative 20 count package for 6 inch square or round.
Image 1 shows cross section of the box with two reversible halves. This is the smallest box available in the word to ship 20 six inch wafers.

This 15 count box is Static Dissipative.  It will hold parts 5mm thick x 153.5mm wide x 115mm tall ( 6.043” x 4.527” x .196” thick).

Static dissipative, reversible box with 25 count molded insert with V groove slots to hold 161.2mm square or round glass. The outer box has 25.4mm wall thickness to provide durable protection.  Insert can be customized to hold your particular glass dimension.

This 20 count box is Static Dissipative.  It will hold parts 171mm wide x 2.8mm thick.
The foam septums (ribs between the glass) extend 29mm into the storage area, you can hold parts as small as 143mm wide and still keep them separated.
Using a flat lid, (#6575-01 lid) you can hold parts 76mm tall.  By using deeper lids, you can hold taller parts, see examples shown in Image #2.  Call for samples and assistance.
This box can be customized to hold your specific size.  See image #3 FOR EXAMPLES of customized boxes using the same exterior size. 
You only pay for the insert to customize the existing box.

Twenty count deep box for 152.4mm squares (6in. squares). Static dissipative.

This 15 count box is Static Dissipative.  It will hold parts 6” square x .170” thick using a flat lid

Static dissipative seven slot tray, stackable.

Static dissipative, reversible box with 20 count molded insert with V groove slots to hold 203.2mm square or round glass. The outer box has 25.4mm wall thickness to provide durable protection.  Insert can be customized to hold your particular glass dimension.

Static dissipative, reversible box with 25 count molded insert with V groove slots to hold 212.2mm square glass. The outer box has 25.4mm wall thickness to provide durable protection.  Insert can be customized to hold your particular glass dimension.

Static dissipative, reversible box with 22 count molded insert(#255) with V groove slots to hold 304.8 mm square glass. The outer box has 25.4mm wall thickness to provide durable protection.  Insert can be customized to hold your particular glass dimension.

Static dissipative, reversible box with height spacer and 22 count molded inserts(#255) with V groove slots to hold 304.8mm x 400mm rectangle glass. The outer box has 25.4mm wall thickness to provide durable protection.  Two spacers can be used to increase the box height to 514mm. Insert and spacer can be customized to hold your particular glass dimension.